KYTECHNGAMING
-
Постов
699 -
Зарегистрирован
-
Посещение
-
Победитель дней
3
Тип контента
Профили
Форумы
Галерея
Загрузки
Блоги
События
Весь контент KYTECHNGAMING
-
yes, turned it off and on after some server and routing setup or ⬇️ restarted it for this reason. -
My hub is Ugreen 3.0 USB Gigabit Ethernet ASIX88179 (https://ugreen.com.tr/urun/ugreen-usb-3-0-gigabit-ethernet-rj45-donusturucu-usb-coklayici/) In addition, the hub is powered by a 5v 3a adapter. There are 2.5" hdd and ssd in 2 ports. I will send the files privately when I repeat the error. thanks.
-
I upgraded my Runner 4g from 3.9.a.5 to 3.9.a.7. I turned on the device for the first time today after posting the latest ipv6 test. After the upgrade, IPv6 appeared to be checked. I think the problem is fixed. https://prnt.sc/_B02walLRK3O
-
Hi @sips , Today I noticed that my voip service has timeout error. It was already working with VPN routing. I checked VPN is ok. I tried the secondary sip server. I saw that it gave either timeout or unauthorized error. Today was a national holiday. I couldn't reach my voip provider. By the way, I am running into this error. Could it be caused by the 3.9.A.7 software version? I'm using Linear plugged in via hub. It can give the same error when removing and plugging. I have also observed that it gives this error even though it is recognized up to the Linear Serial number in the system log. Turning the switch off and on a few times also fixes it. https://prnt.sc/S2-D4Cdx-5t- https://prnt.sc/TNaz2aFvDEyf
-
I guess it's a request for a tapology that doesn't use mesh? 🙄
-
Same on all my devices. Regardless of whether it is a master controller and repeater. But wifi is ok.
-
I noticed this situation in the previous 2-3 FW (3.9.a..) But since I didn't know the logic completely, I didn't know if it was ok or not.
-
It is not available for sale in our country. I didn't pay attention to the features. Pardon.
-
Is it the same situation? I could not fully understand. https://prnt.sc/p_3nMseKAV6P
-
Why is port "0" on the other side seriously? Sfp port and 0 (factory wan port) should be integrated, side by side, right? https://prnt.sc/5073MBvOenEL
-
https://prnt.sc/lKft3JN2-M-L https://prnt.sc/df8AQIVuwQMb Because I use it this way on my other device. This is for local network only.
- 3 152 ответа
-
- 1
-
-
- gpon
- ростелеком
- (и ещё 1 )
-
Yeah. I disassembled a heatsink. In this photo, the module was not fully inserted. https://prnt.sc/I8KuwQxn6sVW If I used the Keenetic upright and rotated the antenna it would be fine. That's why I made the heatsinks that way. But my plan has changed. However, I wish the sfp input and antenna weren't so close by design.
-
It's because it's a twin sim card. So the other sim card was active. Otherwise, I don't have a connection problem. When I took the self-test, it had ip. After 30 seconds, I saw that it was broken. As I said in my first sentence, because of the twin sim card. When available, I can try with only one sim card active. 3g bands are inefficient in Türkiye and even do not receive data. That's why the bands that I can use are selected. I checked with cellmapper before.
-
KN-1011 - ODI and Carlitoxx https://prnt.sc/bRbujWhnsq9n
- 3 152 ответа
-
- 1
-
-
- gpon
- ростелеком
- (и ещё 1 )
-
KN-1011: https://prnt.sc/KnagJ8CnQXE3 KN-2510: https://prnt.sc/y-ZA-0FIGGIe
- 1 ответ
-
- 1
-
-
Hello, I'm not sure my provider supports ipv6. I wanted to enable ipv6 and see results. but I observed that the button does not register. I re-entered the commands in webcli. an ipv6 address was not obtained as a result. Self-test will be forwarded in the next message.
-
I noticed that with KeeneticOS 3.9.a.5, Ipv6 is not activated in modem settings. I entered the commands with the CLI. I can't see any sign that it's active again in the interface. https://prnt.sc/snKQbeRh4gHT The button is not selected. Also, there is no line about ipv6 under ipv4 in the dashboard. If the rope is not provided; it may not come out. I do not know this. https://prnt.sc/rg4mHtgcpMcg
-
https://prnt.sc/EMN9y4Dy4CiY https://prnt.sc/LG6j8Tp2I40C https://help.keenetic.com/hc/en-us/articles/360016127780-Keenetic-Mesh-Wi-Fi-System-frequently-asked-questions-
-
Clear browser's cookie.
-
I asked these questions a long time ago with the advice of the manufacturer Carlitoxx.
-
3.9.A.1 When closing the window in the device setting, the gui looks like this for 1-2 seconds. https://ibb.co/SN2VfRk
-
https://prnt.sc/CsOffkdm7lWD these are my Carlitoxx and Odi sfps. 💙
-
I will check all. Thank you!
-
all ODI clones
- 3 152 ответа
-
- 1
-
-
- gpon
- ростелеком
- (и ещё 1 )
-
Thanks again for your solution. But there is one point that I still don't understand. When I do the routing manually for my ISP, I cannot register. In this case, is my problem the ISP blocking or the location of the sip proxy? WARP (wireguard) solved it while Turkey server was connected.